Crown XLS 802

Crown XLS 802

Crown XLS 802 Description:

The XLS Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. The line consists of four models in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features.

The four models in the series are the XLS-202, XLS-402, XLS-602, and XLS-802. They are identical except for output power and weight.

XLS Series amplifiers are professional stereo power amplifiers engineered to meet demanding audio requirementsreliably and within budget. Plus, every XLS Series amplifier is backed by Crowns unequaled Three-Year, No-Fault, Fully-Transferable Warranty that covers everything. With over five decades of experience designing and building rock-solid products, Crown is the standard in amp technology. So check out the affordable, Crown XLS Series. They are a powerful argument for quality and value!

Crown XLS 802 Features:

• Reliable design incorporates many popular features
• Housed in a rugged, all-steel 2U chassis
• Efficient forced-air fans prevent excessive thermal buildup
• Electronically balanced XLR inputs; touchproof binding post and SpeakonŽ outputs
• Precision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip and fault for each channel.
• Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications

Crown XLS 802 Specifications:

• Power Output (1 kHz*)
• Stereo Bridge-Mono
• 8 Ohm 4 Ohm 8 Ohm
• XLS 802 500W 800W 1600W
• XLS 602 380W 600W 1200W
• XLS 402 300W 450W 900W
• XLS 202 200W 300W 600W
• *1 kHz Power: refers to maximum average power in watts at 1 kHz with 0.5% THD.
• The following applies to units in Stereo mode with 8-ohm loads unless otherwise specified.
• Performance
• Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V.
• Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, -0.8 dB.
• Signal-to-Noise Ratio (20 Hz to 20 kHz)
• A-weighted, below rated power:
• >98 dB.
• No weighting, below rated power:
• >93 dB.
• Total Harmonic Distortion (THD): <0.5%.
• Intermodulation Distortion (IMD):
• (60 Hz and 7 kHz at 4:1) from full rated output to -40 dB: < 0.3%.
• Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
• Crosstalk (below rated power)
• at 1 kHz: -76 dB. at 20 kHz: -58 dB.
• Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.
• Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.
• AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC
• Controls
• Level: Two front-panel rotary level controls, one for each channel.
• Power: Front-panel switch; on when in the IN position.
• Circuit Breaker: Back-panel breaker provides overload protection.
• Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode.
• Indicators
• Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel's input signal exceeds -40 dBu.
• Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel's output is being overdriven.
• Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available.
• Fault Indicator: Two red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on.
• Input/Output
• Input Connectors: One per channel; back-panel three-pin female XLR input connectors.
• Output Connectors: Two 4-Pole SpeakonŽ Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector.
• One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)
• Protection
• XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.
• Construction
• Ventilation: Flow-through ventilation from front to back.
• Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
• Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).
• Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2-inch (38.6-cm) depth.
• Weight
• Net Weight:
• XLS-202: 23.0 lb (10.4 kg)
• XLS-402: 25.7 lb (11.7 kg)
• XLS-602: 29.0 lb (13.2 kg)
• XLS-802: 35.5 lb (16.1 kg)
• Shipping Weight:
• XLS-202: 28.0 lb (12.7 kg)
• XLS-402: 30.7 lb (13.9 kg)
• XLS-602: 34.0 lb (15.4 kg)
• XLS-802: 40.5 lb (18.4 kg)

Get your Crown XLS 802 product today!